• Enraged
  • Embarrased
  • Drunk
  • Down
  • Depressed
  • Crying
  • Crazy
  • Cool
  • Cocky
  • Bemused
  • Awesome
  • Annoyed
  • Angry
  • Amused
  • Friendly
  • Geeky
  • Godly
  • Happy
  • Hateful
  • Hungry
  • Innocent
  • Meh
  • Piratey
  • Poorly
  • Sad
  • Secret
  • Shy
  • Sneaky
  • Tired
  • Wtf
  • Results 1 to 2 of 2

    Thread: Super Space Stranger Cocktail Repair Log

    1. #1
      Kaizen's Avatar
      Kaizen is offline
      is Defending against Invaders
       
      Meh
       

      Join Date
      Jun 2008
      State
      Brisbane, QLD
      Posts
      2,359
      Mentioned
      215 Post(s)
      Quoted
      459 Post(s)
      Australia

      Super Space Stranger Cocktail Repair Log

      I have this cabinet in for repair at the moment.





      https://www.arcade-museum.com/game_d...p?game_id=9946

      http://spacestrangerarcade.blogspot....tranger-2.html

      Manual links:

      https://photos.google.com/share/AF1Q...U1QUZXbnhnTGFB

      https://drive.google.com/open?id=1X7..._iPcGGqpaNTsUO


      The cabinet is in good condition but when first powered up there was no image on screen and not playing blind.
      On closer inspection I found the composite video wire on the edge connector had broken off, it was resoldered and I was greeted by a crosshatch pattern on screen.

      When I pulled the 8 x 2708 ROMs to check them 29 pins were corroded or broken.

      I repaired all the broken pins and dumped them and surprisingly one of the chips that didn't have any broken pins returned a bad dump.
      I burnt a new one and threw them back on the board and it booted up and played without sound.





      The sound amp on these boards is an LM380 which was missing, there were a number of mods (cut traces and link wires) to that section of the board so I went through and confirmed it was correct as per the schematic. It looks like this PCB had a different type amp than what was shown on the schematic but the board has been modded to match it.

      With a new LM380 fitted the board now had the 'footstep' sound only.
      All LM3900 Op Amps were pulled and they all tested faulty.
      New sockets and LM3900's in place and all sounds were restored but the footstep sounds were all the same pitch.



      The resistor array connected to that part of the circuit was replaced with a diy array as I didn't have any 8x1k arrays on hand (only 5 outputs were used so 5x1k resistors were substituted).
      This brought the first three tones back to the correct pitch but the last tone was higher than the previous one. It should be an 82k resistor which tested fine so I substituted it with a 120K (10k+20k in series) which brought the pitch down to the correct level.



      Last thing to do was burn a new set of eproms and replace the sockets.
      The sockets on this PCB are a pain to remove in the normal way with a desoldering gun (the holes are quite hard to desolder completely and with three voltages going into the chips the power rails sink a lot of heat away very quickly).
      With these type of sockets it's easier to pry the top piece off as shown below, then heat the pins up with a soldering iron and push them through the board so the stick out of the socket, then I grab each pin and heat the hole with the desoldering gun and pull the pin out and clear the hole at the same time.



      It's a bit more work but is quite efficient and no lifted pads, tracks or pulled vias.

      New sockets and ROMs fitted and the game is now fully working.





      The only other thing to do is adjust the monitor which I'll get around to tomorrow.

      One interesting thing with this version of Space Invaders is that if you shoot the bases you lose 50 points for every hit.
      The UFO also appears a lot more often than the Tatio/Midway ROM set.
      Last edited by Kaizen; 1 Week Ago at 12:20 AM.
      Namco Starblade - Taito Cocktail 14" x 3, 20" x 2 - NZ SI PtII Upright - Chase HQ DX, Taito Top Speed - Taito Grand Champion - LAI SI Head to Head Cocktail - SI Cocktail Clone x 2, Pong Clone x 3

    2. #2
      poidapoida's Avatar
      poidapoida is offline
      This user has no status.
       
      Happy
       

      Join Date
      Mar 2012
      State
      Brisbane
      Posts
      484
      Mentioned
      19 Post(s)
      Quoted
      105 Post(s)
      Australia
      Thats another rare clone saved. Awesome work.

      Sent from my SM-G925I using Aussie Arcade mobile app

    Thread Information

    Users Browsing this Thread

    There are currently 1 users browsing this thread. (0 members and 1 guests)

    Similar Threads

    1. Perth - Super Space Stranger - Cocktail repairer
      By WinfieldBlue in forum Arcade Machine Restoration Questions and Help
      Replies: 9
      Last Post: 15th November 2016, 04:01 PM
    2. anyone here repair super nintendos ?
      By baz in forum Console Modding and Repair Help
      Replies: 4
      Last Post: 24th May 2012, 10:20 AM
    3. Taito Space Invaders Cocktail Board Repair / Servicing
      By Jango in forum Arcade Technical and Repair Questions
      Replies: 2
      Last Post: 6th March 2012, 10:36 AM
    4. Super pang repair
      By cal2 in forum Arcade Technical and Repair Questions
      Replies: 8
      Last Post: 24th June 2009, 10:41 PM

    Tags for this Thread

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •