Page 6 of 6 FirstFirst ... 456
Results 51 to 57 of 57

Thread: VPGL10 Game 3 Indiana Jones The Pinball Adventure - Williams (finished)

  1. #51
    Join Date
    Dec 2007
    State
    NSW (Newcastle)
    Posts
    1,988
    Mentioned
    73 Post(s)
    Quoted
    727 Post(s)
    Quote Originally Posted by Jed View Post
    Nah, it's just you and JAR.

    And JAR gives you your games, so it's really just JAR

    I've never had a freeze on Indy, but I'm using the 1.1 version as the 1.2 version game me script errors.
    The ones I gave Dedrok were from Wob's cab.

  2. #52
    Join Date
    Dec 2007
    State
    NSW (Newcastle)
    Posts
    1,988
    Mentioned
    73 Post(s)
    Quoted
    727 Post(s)
    Attachment 126677
    Super close this one

  3. #53
    Join Date
    May 2009
    State
    NSW
    Posts
    6,208
    Mentioned
    161 Post(s)
    Quoted
    1428 Post(s)
    this would have to be one of the highest performing/closest games ever, well played everyone.

    I went for a last ditch bash last night but got some Ipac problems everything is fine until I plunge the ball.... flippers work, credits, can start a game, but plunge a ball and the ipac goes dead - light goes off on the board and nothing responds. going to have to dive in and do some rewiring / fiddling with switches, my plunger is dodgy as hell though and pulls a microswitch lever based on a loop of cable ties and fishing line

  4. #54
    Join Date
    Dec 2007
    State
    NSW (Newcastle)
    Posts
    1,988
    Mentioned
    73 Post(s)
    Quoted
    727 Post(s)
    Quote Originally Posted by Jed View Post
    this would have to be one of the highest performing/closest games ever, well played everyone.

    I went for a last ditch bash last night but got some Ipac problems everything is fine until I plunge the ball.... flippers work, credits, can start a game, but plunge a ball and the ipac goes dead - light goes off on the board and nothing responds. going to have to dive in and do some rewiring / fiddling with switches, my plunger is dodgy as hell though and pulls a microswitch lever based on a loop of cable ties and fishing line
    It's not tilting is it? I don't have an explanation but sounds like it is tilting.

  5. #55
    Join Date
    Mar 2011
    State
    Newcastle Australia
    Posts
    6,564
    Mentioned
    390 Post(s)
    Quoted
    1975 Post(s)

    VPGL10 Game 3 Indiana Jones The Pinball Adventure - Williams (finished)

    Funny enough that I spent last night in a Melbourne games room repairing pins and had to fix and play an Indy.

    When he said “go on, have a go of Medieval” I politely declined as I still need to play it here.
    I also kept off the T2.




    Sent from my iPhone using Tapatalk
    The Artist Formally Known As #1

  6. #56
    Join Date
    May 2009
    State
    NSW
    Posts
    6,208
    Mentioned
    161 Post(s)
    Quoted
    1428 Post(s)
    Quote Originally Posted by JustAnotherRat View Post
    It's not tilting is it? I don't have an explanation but sounds like it is tilting.
    No, as the whole Ipac goes dead - not the game. I found out what it was though, totally my fault some bad positioning of a coin door microswitch (plunger button) the backside was pushing up against the lockdown bar lever inside the cab. Bend the pin over and then it bridged onto another terminal. That explains why it went dead whenever I used the hardware plunger or the plunger button as they were wired into the same ipac port.

    Gives me an excuse I guess to tidy up the wiring and do a proper job once I can get a new one. I'm a bit of an out of sight out of mind type guy so it's a bit of a mess in there...

    Nice games room @Dedrok where is that ?

  7. #57
    Join Date
    Mar 2011
    State
    Newcastle Australia
    Posts
    6,564
    Mentioned
    390 Post(s)
    Quoted
    1975 Post(s)
    Melbourne.
    Private collection and that’s just one side.
    Repaired 8 games while playing and eating and talking shit.


    Sent from my iPhone using Tapatalk
    The Artist Formally Known As #1


Page 6 of 6 FirstFirst ... 456

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •