Thanks Thanks:  0
Likes Likes:  0
Results 1 to 5 of 5

Thread: LAST LS Sound Steel Cabinet with VGA29" Screen

  1. #1
    Join Date
    Jan 2006
    State
    Queensland
    Posts
    1,581
    Mentioned
    11 Post(s)
    Quoted
    21 Post(s)

    LAST LS Sound Steel Cabinet with VGA29" Screen

    OK Guys I have this llast unit available....
    For Aussie Arcade Members I will chop of $100...
    Its fully set up ready to go.

    Ideally the setup would be used with a PC system and MAME.
    The monitor is a VGA monitor and uses a standard VGA cable so easy to connect to the PC.
    JAMMA wiring - PSU - 6 Buttons - 4way 240volt power board...

    Check the pictures its all ready to go....

    http://www.gamedude.com.au/arcade/pr...abLS29_31k_10b
    Always interested in Retro and Current gaming

    https://www.gamedude.com.au

  2. #2
    Join Date
    Sep 2008
    State
    Darling Downs, QLD
    Posts
    35
    Mentioned
    0 Post(s)
    Quoted
    0 Post(s)
    I just paid a fortune for one of these thinking it was a tri-sync. I didn't realise it was SVGA ONLY. It looks ok(ish) in 800x600@60Hz and 640x480@60Hz but 15kHz and 25kHz modes don't work at all. It's a very bad choice if you want an authentic MAME experience. Maybe it's ok for people that want a "one size fits all" or "near enough is good enough" solution.

    EDIT: It turns out that these are dodgy dual-focus LG TV tubes with an old PC SVGA monitor chassis hooked up. The geometry is terrible since the combination is not designed to work togetther at all. DODGY!!

    Also, the rear mains panel was arcing due to a bad solder joint that had been bogged up with silicon. The coin mech didn't work at all and it was covered in screwdriver scratches looking as if somebody had been messing with it for hours.

    Most people wouldn't have the balls to sell something like this (especially as "new")
    Last edited by Redmist; 29th July 2011 at 08:28 PM.

  3. #3
    Join Date
    Sep 2008
    State
    Darling Downs, QLD
    Posts
    35
    Mentioned
    0 Post(s)
    Quoted
    0 Post(s)
    ^^ Post edited after further investigation.

  4. #4
    Join Date
    Nov 2006
    State
    bunbury WA
    Posts
    24,378
    Mentioned
    46 Post(s)
    Quoted
    1209 Post(s)
    Should your posts be taken from this thread?

    Its putting no advice towards this sale and be put in its own thread??

  5. #5
    Join Date
    Jan 2006
    State
    Queensland
    Posts
    1,581
    Mentioned
    11 Post(s)
    Quoted
    21 Post(s)

    I dunno what the problem is.... I was never contacted about any issues... the pics of the cabinet clearly show its working OK. And clearly states its VGA plug and screen and suitable for PC systems. The geometry looks fine to me in the pics.....
    As for the coinmech you need to program it first before it works and the scratches are on all the units I have its from the coin holders they are in.
    The add also says its the last one and it is new... as in unused... it still has warehouse dust and the like from over a year of storage on some of it.
    Always interested in Retro and Current gaming

    https://www.gamedude.com.au

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. *SPECIAL* cabinet for DRACER
    By OzStick in forum Mame Cab Projects and Discussion
    Replies: 200
    Last Post: 9th December 2009, 03:47 PM
  2. Cabinet Sound Issue
    By noisuf in forum Arcade Technical and Repair Questions
    Replies: 0
    Last Post: 11th July 2009, 06:41 PM
  3. Who here used a TV in their Mame cabinet?
    By dmworking247 in forum Mame Cab Hardware and Software Discussion
    Replies: 64
    Last Post: 10th December 2008, 10:53 AM
  4. Projectors and Screens
    By WOKA in forum General Chat
    Replies: 32
    Last Post: 4th September 2007, 11:45 AM
  5. Major video developments in MAME
    By The Pinny Parlour in forum M.A.M.E, Computer and Console Emulation.
    Replies: 6
    Last Post: 11th July 2006, 07:49 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •