Search:

Type: Posts; User: wise1

Page 1 of 5 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    533

    So, I took your advice and replaced the diodes. I...

    So, I took your advice and replaced the diodes. I now have 2 working units. still working on the third.
    Thanks for the tip
  2. Replies
    4
    Views
    533

    This got a bit expensive, I bought 2 working...

    This got a bit expensive, I bought 2 working units on ebay usa, had them posted to a remailing mob. add gst. well, both were non working.
    I had to put a 3.15 amp fuse across the switch at CB 1 (same...
  3. Replies
    4
    Views
    533

    ROWE R92 LAMP CONTROL BOARD

    I have a faulty lamp control board - 40821201 for a Rowe R92 jukebox. The lights are on but no flashing. It might not be the board as i just bought this one and Im working through the problems.
    The...
  4. Replies
    2
    Views
    970

    Is this the demo version or did you pay for the...

    Is this the demo version or did you pay for the software?
    Post some pics when your set up is complete. Im also thinking of using this software.
  5. Replies
    6
    Views
    820

    yes, it could be the reed switch

    yes, it could be the reed switch
  6. Replies
    13
    Views
    1,225

    shellite is the product to use for cleaning. buy...

    shellite is the product to use for cleaning. buy from bunnings and cheap as chips
  7. Replies
    23
    Views
    1,454

    Sponsor section, game dude sells these.

    Sponsor section, game dude sells these.
  8. Replies
    5
    Views
    1,040

    I would try buying a serviced/working amp from a...

    I would try buying a serviced/working amp from a dealer/on line. and see if that fixes the problem. if you have the same problem after installing the new amp then you have another issue.
    you could...
  9. Thread: My Aldi JokeBox

    by wise1
    Replies
    14
    Views
    1,611

    its a hobby, dont be so nosey. let him have his...

    its a hobby, dont be so nosey. let him have his fun.
  10. Replies
    84
    Views
    7,011

    I think i used lithium grease but im not sure as...

    I think i used lithium grease but im not sure as it was ages ago. If you do strip it down, take lots of photos, they will help with the rebuild
  11. Replies
    84
    Views
    7,011

    Mate;buy a service guide, paper or disk, and have...

    Mate;buy a service guide, paper or disk, and have a go. If this is too hard then pay some one to fix it
  12. Replies
    84
    Views
    7,011

    Hard to say, the gear box could be gummed up with...

    Hard to say, the gear box could be gummed up with old grease. I think the overload would trip if this was the case. Start at the begining, pull the mech out , clean the gearbox, shellite works well,...
  13. Replies
    6
    Views
    1,220

    You probably have all you need as the Mech.s were...

    You probably have all you need as the Mech.s were a standard item they fitted to a whole range of machines. Rowe Ami did the same.
    I have a manual on cd which covers 404 - 488. Rockola master...
  14. Replies
    6
    Views
    1,220

    Pull the mech out to inspect and blow it with...

    Pull the mech out to inspect and blow it with compressed air, might be a short or the pin (might be made of brass) is stopping a micro switch
    you will have to make a frame to sit the unit on. I...
  15. Replies
    6
    Views
    1,412

    what machine is it? if you list the area you live...

    what machine is it? if you list the area you live in then there might be someone close that can test it for you.
    I try to pick up working spares for my machines when they are available. I sent a...
  16. Thread: NSM repairer

    by wise1
    Replies
    7
    Views
    1,255

    Good luck with your search, NSM repairers are...

    Good luck with your search, NSM repairers are thin on the ground around here.
  17. Replies
    7
    Views
    1,169

    I was thinking your machine was older, MM3 age....

    I was thinking your machine was older, MM3 age. when you said pcb i looked it up.
    if you have replaced the mech control board then look at the opto switch as this might be faulty. it might only be...
  18. Replies
    7
    Views
    1,169

    The scan control unit might be faulty, there is a...

    The scan control unit might be faulty, there is a spring that wraps around a wheel and if there are no more selections,
    this spring will tension then move a lever to hit a micro switch and stop the...
  19. Thread: NSM City II

    by wise1
    Replies
    2
    Views
    617

    From memory, the arm lifts the record from...

    From memory, the arm lifts the record from underneath, then to return it I think it just knocks it back into the rack.
    so something out of sequence. check the operation of the lifting arm, does it...
  20. Replies
    2
    Views
    730

    Im not sure what DS2 is, but i would start by...

    Im not sure what DS2 is, but i would start by re-seating and/or replacing all the spade connectors on top of the lid (mine is R88 and they are located on the lid above the amp)
    If DS2 is an...
  21. Replies
    8
    Views
    1,537

    $400-$600. that's my price range for Rowe Ami....

    $400-$600. that's my price range for Rowe Ami. Rockola would be the same. A dealer would want another 1k on top of that.
  22. Replies
    12
    Views
    2,178

    What condition are the wires on the record...

    What condition are the wires on the record basket? on machines of this age the zinc plating is usually very rough.
    jukeboxes are never very kind to vinyl.
  23. Google, Arcade controls forum :)

    Google, Arcade controls forum :)
  24. Try AMI Man on Arcade controls forum.

    Try AMI Man on Arcade controls forum.
  25. Replies
    2
    Views
    480

    Try Arcade Controls forum, The Rowe Ami blokes...

    Try Arcade Controls forum, The Rowe Ami blokes hang out there, Bruce Wentworth is in the USA, Alan Hood UK
Results 1 to 25 of 121
Page 1 of 5 1 2 3 4