Search:

Type: Posts; User: lavalyte

Page 1 of 10 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    29
    Views
    6,184

    Have you considered writing an article for...

    Have you considered writing an article for Retrogamer magazine?
  2. I've seen them there before... they've had them...

    I've seen them there before... they've had them for a year or so in there because the prices are too high.
  3. Replies
    2
    Views
    268

    Logic probe is slightly above my level of...

    Logic probe is slightly above my level of understanding at this point.
    I'll have a look at the ports though.
  4. Replies
    2
    Views
    268

    Stuck button on Neo Geo MVS MV1C

    I have a MV1C board that always a shows a stuck P1 D button.
    I can see no issue on the board in terms of shorts.
    I have replaced the resistor array at the front right (facing the JAMMA edge) but no...
  5. Replies
    23
    Views
    1,575

    Slightly off topic, but do you do atari 7800...

    Slightly off topic, but do you do atari 7800 s-video mod boards?
  6. Replies
    43
    Views
    2,371

    So that converts RGBS through SCART?

    So that converts RGBS through SCART?
  7. Replies
    29
    Views
    6,184

    You're right, I've been playing too much SNES mr...

    You're right, I've been playing too much SNES mr Do.
  8. Replies
    29
    Views
    6,184

    bigredbird One trick you've missed. When you...

    bigredbird
    One trick you've missed.
    When you release the alphamonster and the munchers, the alphamonster will always initially go left down the tunnel and the chasers will go right, so you can head...
  9. Replies
    14
    Views
    1,253

    I have a 13 inch crt and harness that needs...

    I have a 13 inch crt and harness that needs reconditioning, if its any use to you.
  10. Replies
    6
    Views
    3,597

    For what it's worth I handed this off to another...

    For what it's worth I handed this off to another modder with more experience than I, and he couldn't get it working either.
  11. Replies
    2
    Views
    415

    Possible Birthday Mania

    I've been offered a Birthday Mania atari cart... but with no circuitboard in it.
    I am wondering if there's any way to validate it.
    At this point I am working off photos.

    - - - Updated - - -

    I...
  12. Replies
    2
    Views
    691

    Oh I know. I tried all that, in and out, fully...

    Oh I know. I tried all that, in and out, fully in, mostly in etc. I'll give it another shot though.
  13. Replies
    2
    Views
    691

    Neo Geo 161 in 1 has died

    I have a 161 in 1 in a CMVS that I haven't fired up for a couple of months.
    I did so and got a screen of random blocks and no games.
    CMVS works fine for other carts.

    I've cleaned the contacts....
  14. Replies
    9
    Views
    1,590

    I have one of these on order to spruce it up a...

    I have one of these on order to spruce it up a little... fancy coin button

    - - - Updated - - -

    I'm also considering putting in a volume control into the bottom of the coin panel.
  15. Replies
    9
    Views
    1,590

    Nominally complete with LCD. I want to switch to...

    Nominally complete with LCD.
    I want to switch to CRT at some point.

    113741113742
  16. Replies
    27
    Views
    2,632

    It was worth a shot but no luck. - - - Updated...

    It was worth a shot but no luck.

    - - - Updated - - -

    Seeing as the VGA signal is fine, I'm going to order a VGA to CGA board and run through that. I can see the board allows the image to be...
  17. Replies
    27
    Views
    2,632

    After looking up the schematic, there are these...

    After looking up the schematic, there are these adjustments on the chassis....

    113406

    of those adjustments the three on the left are difficult to get to, the four on the right are easy.
    I've...
  18. Perhaps my terminology isn't correct. Isn't this...

    Perhaps my terminology isn't correct. Isn't this from your renovation?

    pic
  19. For what it's worth looking at your old surrounds...

    For what it's worth looking at your old surrounds you could recondition them by sticking a thin sheet of mdf under them and filling the gaps with epoxy glue so it's a nice flat surface, then spray...
  20. Replies
    27
    Views
    2,632

    Gave it a shot, and talked to a pc refurbishing...

    Gave it a shot, and talked to a pc refurbishing place.
    Unfortunately no-one takes in 13 inch CRTs or LCDs these days. The refurbisher only kept 17 inch +.
  21. Replies
    27
    Views
    2,632

    The tricky part is, the cab only takes a 13 inch...

    The tricky part is, the cab only takes a 13 inch screen and I don't want to alter it too much. Hard to find a 13 inch lcd or crt monitor these days.
  22. Replies
    27
    Views
    2,632

    It's frustrating, because apart from missing that...

    It's frustrating, because apart from missing that little bit of the top/left, the image is beautifully clear.
  23. Replies
    27
    Views
    2,632

    I got a vga cable today and the vga output is...

    I got a vga cable today and the vga output is fine.
    I notice the vga outputs at 60hz so I wonder if the cga is also at 60hz, which might not be ideal for an australian amiga monitor.
  24. Replies
    27
    Views
    2,632

    For what it's worth I plugged a neo geo board in...

    For what it's worth I plugged a neo geo board in and I can see the entire neo geo test pattern.
  25. Replies
    27
    Views
    2,632

    Not sure about that. I have controls to adjust...

    Not sure about that.
    I have controls to adjust the vertical and horizontal width and centering, and there is no adjustment that will shift the unseen part of the image into visbility. Note that the...
Results 1 to 25 of 237
Page 1 of 10 1 2 3 4