Search:

Type: Posts; User: Kaizen

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    29
    Views
    7,714

    If you are making a PCB the has to line up...

    If you are making a PCB the has to line up perfectly you can export the PCB to PDF as 1:1, print it off and check it lines up. Same for pin spacing, it's hard to tell when looking at it on screen but...
  2. Replies
    5
    Views
    132

    Should be an S6 mech in that cab, I have a couple...

    Should be an S6 mech in that cab, I have a couple you can have.

    Page 46-47...
    https://archive.org/details/arcademanual_LAISEGA_Outrunners_Manual
  3. I have plenty of new 14.31818 crystals in stock...

    I have plenty of new 14.31818 crystals in stock mate, shoot me a PM if you think they'll do the job.
  4. Replies
    29
    Views
    7,714

    Nice work, I have a few lots of boards from first...

    Nice work, I have a few lots of boards from first revisions with minor errors the can be fixed with trace cuts or jumpers. Even though they only cost a few bucks I can't bring myself to throw them...
  5. Replies
    4
    Views
    1,747

    https://www.altronics.com.au/p/s4063-globe-wheat-1...

    https://www.altronics.com.au/p/s4063-globe-wheat-12v-60mah/
  6. Replies
    17
    Views
    530

    The first revision of the streamimg adapter has...

    The first revision of the streamimg adapter has been built and tested, the audio out needed tweaking, line out is now a 3.5mm jack and I've changed the output to Scart to make it connect to the OSSC...
  7. Replies
    5
    Views
    247

    Is it in an original Nintendo cocktail cabinet?

    Is it in an original Nintendo cocktail cabinet?
  8. Job's done... https://i.imgur.com/5jwKMzk.jpg

    Job's done...

    https://i.imgur.com/5jwKMzk.jpg
  9. Nice work mate, I just started another print with...

    Nice work mate, I just started another print with new tape and upped the temp by 20 degrees and it's laying down nicely.
    Speed is set at 40% so it will take a while, currently at 3% after 30 mins.
    ...
  10. Replies
    11
    Views
    320

    Yeah, having it work like an original cab...

    Yeah, having it work like an original cab (without memory carda) is most important, the games won't be swapped too often and I plan to create a few batch files with different game combinations.
  11. Replies
    11
    Views
    320

    I just created the Roms folder manually. I...

    I just created the Roms folder manually.

    I didn't want the memory card option to load/save games so I've edited the command to...

    mame64 neogeo -cart1 mslug -cart2 mslug2 -cart3 mslug3h -cart4...
  12. Replies
    11
    Views
    320

    Brad Edit: Got it working, syntax error on my...

    Brad

    Edit: Got it working, syntax error on my part...

    Thanks for taking the time to write the tutorial up.
  13. Replies
    11
    Views
    320

    Just setting it up now, will let you now how I go.

    Just setting it up now, will let you now how I go.
  14. Done a couple attempts at printing the cart with...

    Done a couple attempts at printing the cart with the new filament but it doesnt want to stick to the tape.
    Will get some fresh tape, up the temp and try again.
  15. Replies
    11
    Views
    320

    Awesome, thanks for the replies. Will set up a...

    Awesome, thanks for the replies.
    Will set up a new PC and try it out tonight.
  16. Replies
    11
    Views
    320

    MAME Neo Geo 4 and 6 Slot Setup

    Has anyone set up Mame to emulate a 4 or 6 Slot Neo Geo board.
    Was hoping someone can give me some direction or do a quick setup tutorial ie Mame version etc.
  17. Replies
    17
    Views
    530

    Okay, let me know if you find some at a...

    Okay, let me know if you find some at a reasonable price other than Aliexpress.
  18. Replies
    17
    Views
    530

    Sorry mate, they've been tested on the first run...

    Sorry mate, they've been tested on the first run and all good, yeah I should have two spare.
    Will test one first tomorrow and confirm there's no issue with this run.
    If all good then I'll shoot you...
  19. Replies
    17
    Views
    530

    I've just built and tested the one with RCA...

    I've just built and tested the one with RCA outputs and it needs debugging.
    There's an issue with the Sync Cleaner circuit and somehow I got the RCA connector pinout arse about, once I get the the...
  20. Replies
    5
    Views
    187

    Credit PCBs arrived today, both tested and...

    Credit PCBs arrived today, both tested and working.

    https://i.imgur.com/ldZRHXH.jpg

    I could only order 30 of the small PCBs in a small batch order otherwise it would have taken a few more days...
  21. Thread: LM3900 Tester

    by Kaizen
    Replies
    5
    Views
    632

    I decided to give this an upgrade and designed a...

    I decided to give this an upgrade and designed a PCB for it that will fit in a hand held enclosure.

    https://i.imgur.com/AeP0CSC.jpg

    https://i.imgur.com/Lth5j2p.jpg

    ...
  22. Replies
    14
    Views
    948

    Video Board Fault - Graphics Glitch Above The...

    Video Board
    Fault - Graphics Glitch Above The Top Ladder

    https://i.imgur.com/vtwLYBi.jpg

    The glitch only appears on the barrel screen when the sprites are moving.

    I've had this issue on a...
  23. Can't help with the insides of it but spotted...

    Can't help with the insides of it but spotted this in EA Magazine Feb 1976.

    https://i.imgur.com/9iuKoWe.jpg
  24. My bad, when searching I got C64 in my head. ...

    My bad, when searching I got C64 in my head.

    I'll start a test print with the remaining filament I have.
  25. Looks like that one is done in ABS, it has a...

    Looks like that one is done in ABS, it has a shine to it.
    PLA will come out a lot rougher.

    Would one of these be better or is the internal shape designed to fit the PCB you are using?
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4