Jump to content

hotty

Veteran
  • Posts

    3,967
  • Joined

  • Last visited

Everything posted by hotty

  1. Confused, yes, but im glad it’s working cos I’m out of ideas too. You’re a smart cookie and know only one will illuminate in circuit but have you actually tried to test each led with a couple of volts on its legs to see if they actually illuminate? TX side is basically 12v and a resistor to the board its the RX that has more circuitry and generally where the issues exist.
  2. That could be the case with the board sets as the wires will be addressed to the switch matrix however its the LEDs at a component level that it makes no difference. Same as the Bally/Williams opto TX assembly it doesn’t care one way or another if actual TX IR’s are swapped around as long as the RX it gets its light source. But replacement boards eg great lakes opto boards really want the matching pair as per switch matrix specs because of the diagnostic features.
  3. @robm Hi Rob, OK I know the original LED is MT5000UR Ultra Bright T-1 3/4 Marktech optoelectronics it may be discontinued now but I know with the specs given you will find a replacement or NOS. Now is the type your chasing a through hole design or is it the SMD? SMD's I have. The schematic is out of Baywatch as I was repairing Independence Day but as you can see the write up and operation is exactly the same. I also replaced the LM311N comparitor and 2N3904 I just did at the time. It was a long time ago. I did experiment at the time but the LED really needed a precise focal point to work effectively. So using resistors or trying to increase light output wont work but probably fail prematurely. It's all about narrow beam so you don't get flooding or interference from near by light output. It's a much better design than IR as you can visually see if the TX is working. Both sides use the same LEDs. Attached is the link to the MT5000UR data spec. it's safe to click. Hope this helps mate. https://www.datasheets360.com/part/d...9802010253818/
  4. I will have a look generally I document these things.
  5. @robm i had an LED opto issue with the alien head on Independence day. The optos are bright clear lens red light standard looking LEDs not I R so shining a torch into the RX should trigger a switch I also repaired a WPT that are surface mount . I purchased the LEDs from RS components and rreplaced them on board they were on. They do have a particular wave or focus spread.Hi
  6. You sure its not Richard Clapton impersonating Steve Ritchie?
  7. SR is there to repopulate G n R playfields to send to existing buyers, its part of his internship with JJP.
  8. ​ Luv it, well put. JJP discussing what all the fuss is about.
  9. Well that explains the cricket bats as the final clue...... It’s Spinal Tap
  10. And to be fair under some duress they handled it differently too with a much better outcome.
  11. I’m confident its Spinal Tap as the cryptic slogan in the OP ‘To 11’ refers to the band member explaining that his amp dials go all the way To 11. It’s 1 louder. Also the 7/11 reference ties in with a promo that the store uses in an advertising campaign, “Take it to 11�
  12. What about a DC to AC inverter and then use a standard arcade power supply? Depending on power requirements could be as little as $50
  13. I’ll help her get rid of your stuff, and show her that note you wrote telling me to take a couple of machines because Ive been such a good friend 🤣 I bet you’re warning her right about NOW!
  14. Yours is now Sold! I have a buyer who’s willing to pay $130,000 after talking me down from $185000. Should I trust this guy he even wants free delivery? Come on Shannon this whole deal stems on free delivery 🤣
  15. I love seeing these prices and the reactions they draw. Gives reason to drive up the price for the next NIB or manufactures to increase prices during a production run.
  16. I am lead to believe the the ducks will be an interactive shooting gallery as the topper.
  17. Your idea’s end in tears.
  18. Well 3 months on since I started this thread and now a tri-state lockdown. I’m in lockdown fatigue, so iI purposely walk 10 km’s for a morning coffee.
  19. Sell it back on Lloyds for 50x what you paid for it. It’s bound to grab the attention of deep pockets. Great job by the way.
  20. Mimic the same lamp holder and put the diode if you can just in case you use a globe standard globe but if using an led its a diode in itself so there’s probably no need to
  21. Try searching IPDB its all there also any DE switch matrix for that era will help.
  22. Im sure he will get offers he is a retailer, maybe drop a small deposit to secure it because your terms are pending on conditions.
  23. @spaceballs If you do find the adhesive isn’t what it use to be they’re not a total loss, so don’t throw them out, just apply low tack adhesive from an aerosol. I have used spray can adhesive in making my own stencils in the past.
  24. I think with our climate and evaporative cooling and heating its bound to affect the adhesive properties over long term storage in under the bed in the house.
×
×
  • Create New...