Announcement

Collapse
No announcement yet.

Addams Family display driver board

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Addams Family display driver board

    Hello all. Can anyone point me in the right direction please? I need to purchase a new display driver board for an Addams family. Would like a new one if possible. I believe the part number is 5760-12710-00. Thanks in advance. P.s. preferably here in Oz.

  • #2
    Originally posted by Bishop View Post
    Hello all. Can anyone point me in the right direction please? I need to purchase a new display driver board for an Addams family. Would like a new one if possible. I believe the part number is 5760-12710-00. Thanks in advance. P.s. preferably here in Oz.
    Whats wrong with your old one?

    Comment


    • #3
      whats the problem with the old one?

      Comment


      • #4
        Originally posted by Boots View Post
        Whats wrong with your old one?
        Originally posted by judgeboz View Post
        whats the problem with the old one?
        SNAP!

        Comment


        • #5
          All I know is it doesn’t work properly. I have swapped it with another one and the display works fine. The other one looks a bit toasty at the bottom on the back side. It still works, (just), but not as bright and has almost half of it lost when it’s on the display.

          Comment


          • #6
            Hey [MENTION=15961]Bishop[/MENTION] been a long time mate

            Most display board problems can be fixed, typically the high voltage section at the bottom of the board goes and needs the components replaced. Send the board to Ken [MENTION=434]Skybeaux[/MENTION] who can do the HV repair and test the board fully (has a WPC testbed). Itíll be cheaper than replacing the board


            Sent from my iPhone using Tapatalk

            Comment


            • #7
              Brett is right - possibly an issue with one of the high voltage circuits going out of spec. You'd need to check the voltages to confirm. Are you in Sydney? If so, I can fix it up for you - bring it around today if you're free. Otherwise Ken is the best bet.

              http://www.afpinball.com
              "Pinball... harmless recreation for a modest consideration"

              Comment


              • #8
                Where are you in Sydney?

                - - - Updated - - -
                [MENTION=17088]Manny65[/MENTION] no too bad mate. Still got TZ? I should have told you it was a bad buy and got that for myself!!! LOL

                Comment


                • #9
                  Haha yep still have it. Currently stripped down and waiting to be restored


                  Sent from my iPhone using Tapatalk

                  Comment


                  • #10
                    Originally posted by Bishop View Post
                    Where are you in Sydney?

                    - - - Updated - - -
                    [MENTION=17088]Manny65[/MENTION] no too bad mate. Still got TZ? I should have told you it was a bad buy and got that for myself!!! LOL
                    Campbelltown. Free today also if you still need it done.

                    http://www.afpinball.com
                    "Pinball... harmless recreation for a modest consideration"

                    Comment


                    • #11
                      [MENTION=15961]Bishop[/MENTION] +1 for Ken @Skybeaux to fix it, You can't be in better hands.
                      Gemini2544's 4th Pinball meet Saturday 21/03/2020

                      Comment


                      • #12
                        For some reason I didn’t think [MENTION=434]Skybeaux[/MENTION] did these boards. Will have to give Ken a call.

                        Comment


                        • #13
                          Originally posted by Bishop View Post
                          For some reason I didnít think [MENTION=434]Skybeaux[/MENTION] did these boards. Will have to give Ken a call.
                          Yep heís done several of my WPC DMD controller boards


                          Sent from my iPhone using Tapatalk

                          Comment


                          • #14

                            Comment


                            • #15
                              Ken repaired my TZ boards a couple of years ago did a great job and reasonable with his charges .

                              Comment

                              Users Viewing Topic: 0 members and 1 (guests)
                              Working...
                              X