PDA

View Full Version : Hankin Logo



Wob
31st July 2009, 04:52 PM
I am considering replacing the glass on my newly acquired Hankin cocktail, it doesn't currently have the hankin logo (just the borders) I like the look of the logo's and would like to reproduce them.

I have only managed to find some average photo's of the logo, wondering if one if the Vector Wizards could convert from one of them? Or if there is someone out there that has the logo on a machine if they could take a nice high res macro shot of it.

I have had a crack at vectorising it, but without much success, it shouldn't be hard for someone that knows what they are doing :)

Cheers,
Beau

12026

12028

12029

spacies
31st July 2009, 06:56 PM
Calling Spriggy!!!!

Lazarus
31st July 2009, 07:21 PM
That last picture should be sufficient.

If I knew how to do it, i would....lol


anyone ???

spacies
31st July 2009, 07:30 PM
Nah, no good. Needs to be a high res phot at the least or if you want it perfect then it needs to be scanned.

spriggy
31st July 2009, 07:54 PM
Calling Spriggy!!!!

Smart Ass! :D:cool:

Wob,

You talking about the Shark Fin logo?

Wob
31st July 2009, 08:21 PM
Nah mate, just the Hankin text logo.

spriggy
31st July 2009, 08:37 PM
Nah mate, just the Hankin text logo.


I was going to say ... Hankin shark logo ?? :blink: ;)

Without a decent snapshot . I'll be guessing on sizes etc. If you can't get a scan .. at worst .. get someone to take a clean over-the-top high megapixedl photo of the logo, plus measurements. IE the height of the 'H' and 'K' legs and the over-all width. Then we get sort out scale easy.

20 minute job. So happy to do if you can give me the above.

Pash
31st July 2009, 08:39 PM
If you need a scan of the wording I can probably do that tomorrow. Just need to grab the plastic off one of the pins and scan it in.

Wob
31st July 2009, 10:47 PM
If you need a scan of the wording I can probably do that tomorrow. Just need to grab the plastic off one of the pins and scan it in.

That would be great if you can.


I was going to say ... Hankin shark logo ?? :blink: ;)

Without a decent snapshot . I'll be guessing on sizes etc. If you can't get a scan .. at worst .. get someone to take a clean over-the-top high megapixedl photo of the logo, plus measurements. IE the height of the 'H' and 'K' legs and the over-all width. Then we get sort out scale easy.

20 minute job. So happy to do if you can give me the above.

Most appreciated.

Can someone with a Hankin take some dimensions for us and or a nice high res photo?

Cheers,
Beau

spriggy
31st July 2009, 11:18 PM
That would be great if you can.



Most appreciated.

Can someone with a Hankin take some dimensions for us and or a nice high res photo?

Cheers,
Beau


For something that simple mate, a good scan will be fine. The measurements were only if I had to use a digital photo. Maybe just a general horizontal measurement from H to K as a check

Lazarus
2nd August 2009, 11:50 AM
Whoever is making these has the font :)

http://cgi.ebay.com.au/Brand-New-Hankin-Arcade-Video-Game-Tabletop-60-Games_W0QQitemZ310157963012QQcmdZViewItemQQptZLH_D efaultDomain_15?hash=item4836daef04&_trksid=p3286.c0.m14#ebayphotohosting

Does anyone know if they lurk here?

Davefjedi
2nd August 2009, 11:54 AM
Yes David from Bumper Is a member on here

Wob
3rd August 2009, 08:46 AM
I have actually emailed, bumper and a couple of other places that stock those units requesting information on supplying Glass, stickers or artwork. But I don't really fancy my chances of a positive response.

Wob
29th September 2009, 04:12 PM
Hey guys, I am still looking for a good version of the Hankin Logo. So far mooncresta is the only one I have found with it but he doesn't have a Scanner or Good Camera to get it into digital form.

If need be I'll try and get down there and photograph them but times limited at the moment, anyone else out there with the logo and the equipment to scan\photograph it? Or anyone a little closer to mooncresta (Central Coast) than I am?

Just as a note, I need a nice square photo of the logo, taken from directly above or a scan. I will also need some measurements such as overall size (width\height) and some of the letter widths.

Cheers.
Beau

Bump
29th September 2009, 06:26 PM
I can vectorise it from a square photo no worries Wob. Just send me the file and it shall be dun. :)

edit: if all u can get is a file taken from an angle, I should still be able to stretch it back and then vectorise. let me kno.

Mr_Staypuft
30th September 2009, 03:28 PM
Hey guys, I am still looking for a good version of the Hankin Logo.
So far mooncresta is the only one I have found with it but he doesn't have a Scanner or Good Camera to get it into digital form.

If need be I'll try and get down there and photograph them but times limited at the moment,
anyone else out there with the logo and the equipment to scan\photograph it?
Or anyone a little closer to mooncresta (Central Coast) than I am?

Cheers.
Beau

As someone who'd also benefit, I'm happy to chip in a few bucks to some Central Coast-based AA member
who might be able to visit Mooncresta & photograph his Hankin logo for us.

Lazarus
30th September 2009, 06:38 PM
As you're aware Wob - I'm also very interested in this, so please let me know if I can help somehow. I'll watch the thread closely.

Bump
1st October 2009, 09:17 AM
Morning lads.

Here's the Hankin logo vectorised in super black.

Difficult to tell if some of the edges are rounded at that resolution but it should be pretty close.

Also measured yer cocktail Wob so its the same height as the one on the pic.
Ends up almost 18mm high.

Let me know if anyone else has any requests.

Lazarus
1st October 2009, 09:22 AM
I just wet my pants.... thanks!!

Wob
1st October 2009, 09:24 AM
Very nice work Mr Bump, I will see if "mooncresta" can print it and see how it lines up to the original.

Just need to look into having these printed as vinyl stickers, would want to be reversed and stuck on the underside of the glass.

cejay
1st October 2009, 09:38 AM
Awesome work!!

Claude
1st October 2009, 10:29 AM
Great work there Bump.

Can you give us a rough idea of the process you went through to get it done?

Cheers,

Claude

Roxbury
1st October 2009, 12:37 PM
Just need to look into having these printed as vinyl stickers, would want to be reversed and stuck on the underside of the glass.

Thats exactly the thought I had!

Bump
1st October 2009, 01:39 PM
With black vinyl, although the sticky side is still black it isn't as nice a finish as the non-stick side. Is there a preference to use the glass over the machine? dust or scratches from glass moving? I'll attach a reversed image for both choices.




Great work there Bump.

Can you give us a rough idea of the process you went through to get it done?

Cheers,

Claude

1) Grab Wob's photo and drop it into Illustrator.
2) Tilt it so its flat and set up some guidelines.
3) Get tracing with the pen tool and make sure everything is level Your bezier curves need to lead accurately into any straight lines attached to them.
Oh and important to use smart guides so she's all crisp.

If anyone needs the black lining around the glass edges done too, let me kno. Wobs is still in my dungeon and wont be any trouble to measure up.

Mr_Staypuft
1st October 2009, 02:45 PM
Oooooh, Hankin-cocktail-owners group hug for Bump! :cool:

Bump
2nd October 2009, 12:36 PM
I've traced out all the borders for the hankin cocktail cabinet here.
(reversed for vinyl application to the glass)

This one was a bit trickier but got there in the end.

Edit: file updated (Hankin logo made slightly smaller as per original artwork provided to Wob by Mooncresta)

Lazarus
2nd October 2009, 12:41 PM
very good.

Do you have the dimensions by any chance?

Bump
2nd October 2009, 02:38 PM
Yup

The outside glass was 804x602mm
The outer black edge came in around 3mm inside that, leaving the outer dimensions as 798x596mm.

The inside border around the monitor is 487x487mm (14mm thick) which leaves a clear area of 459x459mm.

Claude
2nd October 2009, 05:04 PM
Wow. Makes me want to build a Hankin replica now!

Well done.

Bump
6th October 2009, 10:03 PM
Scaled logo as per dimensions given to me by Wob.
74mm wide along the bottom. And tho the 'n' comes out at about 10mm high the 'H' Isn't quite 17mm. Did you need it scaled on the border file too?

Lazarus
6th October 2009, 10:27 PM
timing is awesome - I was just about to email the printers...

thankyou very much

Bump
8th October 2009, 04:33 PM
"Hankin_Borders_rev.pdf" file has been updated in previous post to the same scaled size as the updated scaled logo.

(The Hankin logos were made slightly smaller to conform to the exact sizing provided to Wob by Mooncresta)

Jango
3rd February 2013, 09:57 PM
Guys, anyone have any idea what a printer would charge to print something like this Hankin border and put onto glass?

Roxbury
4th February 2013, 05:49 AM
When I got mine done it cost $40 to make a vinyl sticker cut out and have it put on the glass.

DiGiTaLJaM
3rd August 2017, 07:09 PM
Awesome, thanks for sharing these, it will come in handy :D

Homepin
3rd August 2017, 08:51 PM
Awesome, thanks for sharing these, it will come in handy :D

Holy thread resurrection Batman!!

sriley50
4th August 2017, 02:52 PM
What!! its only 4 1/2 years old, I'm sure I have seen older!!!! :lol

Wob
4th August 2017, 11:07 PM
And my machine is still in a state of restoration [emoji849] I have all the parts, just need to put them all together. Life and other projects got in the way

Sent from my SM-G935F using Tapatalk