• Enraged
  • Embarrased
  • Drunk
  • Down
  • Depressed
  • Crying
  • Crazy
  • Cool
  • Cocky
  • Bemused
  • Awesome
  • Annoyed
  • Angry
  • Amused
  • Friendly
  • Geeky
  • Godly
  • Happy
  • Hateful
  • Hungry
  • Innocent
  • Meh
  • Piratey
  • Poorly
  • Sad
  • Secret
  • Shy
  • Sneaky
  • Tired
  • Wtf
  • Thanks Thanks:  0
    Page 1 of 2 12 LastLast
    Results 1 to 10 of 18

    Thread: Can't remove torx bolt

    1. #1
      garryi is offline
      This user has no status.
       
      ----
       

      Join Date
      Aug 2016
      State
      NSW
      Posts
      51
      Mentioned
      2 Post(s)
      Quoted
      11 Post(s)
      Australia

      Can't remove torx bolt

      The bolt for some reason would not screw back on (too big)

      I tried using pliers with plenty of force and it won't undo

      Any ideas?



    2. #2
      robm's Avatar
      robm is offline
      This user has no status.
       
      ----
       

      Join Date
      Dec 2008
      State
      Townsville
      Posts
      2,515
      Mentioned
      113 Post(s)
      Quoted
      509 Post(s)
      Vice grips?

      Sent from my SM-G930F using Tapatalk

    3. #3
      wiredoug's Avatar
      wiredoug is online now
      is running out of clever status
      messages
       
      Drunk
       

      Join Date
      Mar 2013
      State
      Derrimut, Victoria
      Posts
      5,664
      Mentioned
      230 Post(s)
      Quoted
      2000 Post(s)
      Australia
      heat? ( big soldering iron maybe?)

    4. #4
      c_mario is online now
      This user has no status.
       
      ----
       

      Join Date
      Jun 2013
      State
      NSW
      Posts
      191
      Mentioned
      3 Post(s)
      Quoted
      56 Post(s)
      Australia
      Angle grinder, then drill it out and retap the thread.

    5. #5
      steptoe's Avatar
      steptoe is online now Zzzaap, zap BANG..!
      is is Is looking for donkey kong,
      astroids, dig dug, moon patrol
      cabs etc
       
      ----
       

      Join Date
      Jan 2007
      State
      Bathurst NSW
      Posts
      1,159
      Mentioned
      31 Post(s)
      Quoted
      140 Post(s)
      Vicegrips, less work as possible

    6. #6
      jason1's Avatar
      jason1 is offline
      is Olivia's Penny Arcade
       
      ----
       

      Join Date
      Apr 2012
      State
      qld
      Posts
      1,677
      Mentioned
      44 Post(s)
      Quoted
      426 Post(s)
      Australia
      Quote Originally Posted by c_mario View Post
      Angle grinder, then drill it out and retap the thread.
      If I had a dollar for all the Times Ive had todo that, lol.

      If the vice grips fail out comes the Grinder and the drill, Might give the screw extractor ago if im feeling keen
      My restorations page www.oliviaspennyarcade.com

    7. #7
      Autosteve is offline
      This user has no status.
       
      ----
       

      Join Date
      Dec 2016
      State
      Barden Ridge NSW
      Posts
      468
      Mentioned
      10 Post(s)
      Quoted
      161 Post(s)
      Australia
      A mix of all above. WD40 on the tread and try to screw it back in only so the WD40 can get into the thread of the nut and then continue trying to get it out with vice grips.

      You have checked to see no nut is on the bolt the other side of the tapped thread haven't you?.

      If still no go, 1mm cutting disc on an angle grinder and try cutting a slot in the head for a large flat head screw driver, ( only if you have a large flat head screw driver with a square shaft you can get a shifter on the square shaft to turn)

      Flat piece of steel, 5mm X 30mm with a hole drilled in it so it sits on, not over, the head of the bolt and mig weld the bolt head through the hole to the steel.

      This will not only give you a large piece of flat steel welded to the bolt head to grab and turn but also heat the thread and heat always helps to free up bolts that are frozen.

      If the bolt snaps, drill it out and retap the thread.

    8. #8
      arcadus's Avatar
      arcadus is offline Archaic Mumble****er
      is C@#tiverous
       
      Godly
       

      Join Date
      Dec 2006
      State
      South Australia
      Posts
      1,905
      Mentioned
      2 Post(s)
      Quoted
      52 Post(s)
      Zambia
      Using a pair of side cutters just below the head, without squeezing too hard and cutting the head off, can bite into the thread enough to move it a little.
      EM score motors wanted: nonworking or working
      Sega Sub Roc 3D periscope mech. needed except motors.
      Wanted, Mitsubishi 60" RP (vs 6041) complete TV gun assembly. (R Proj TV/monitors and parts taken away).
      Take Five pinball machine PCB wanted.

    9. #9
      sparkythepinmonkey's Avatar
      sparkythepinmonkey is offline sumatoboruki saru
      is stuck fixing everyones
      'too hard' jobs. Daijoubunai!
       
      Bemused
       

      Join Date
      Mar 2007
      State
      South Australia
      Posts
      409
      Mentioned
      3 Post(s)
      Quoted
      29 Post(s)
      It's probably got some 'He-Man' strength thread-locker on it.
      If you can access the back of the screw, hit it with either a gas torch, or a soldering iron for 30 seconds.
      You will be amazed at how easy it comes out with a bit of heat.

    10. #10
      jason1's Avatar
      jason1 is offline
      is Olivia's Penny Arcade
       
      ----
       

      Join Date
      Apr 2012
      State
      qld
      Posts
      1,677
      Mentioned
      44 Post(s)
      Quoted
      426 Post(s)
      Australia
      Is it stainless into Alloy? if so thats the problem
      My restorations page www.oliviaspennyarcade.com

    Page 1 of 2 12 LastLast

    Thread Information

    Users Browsing this Thread

    There are currently 1 users browsing this thread. (0 members and 1 guests)

    Tags for this Thread

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •